吸附性式干澀機

◆新產品特性 Product features

※都具有平穩高度的撒氣壓為和露點

1.吸收塔之高與直徑約經實踐效果精密鑄造計算出來，塔床內壓小，衡量了進行壓縮甲烷氣體干熱劑5秒的了解時光，考慮半成品氣的露點想要。

2.30％的缺水劑總流量，用作補賞缺水劑的肯定老化試驗，保證缺水。

3.大中型擴散轉移器，保證 氣體飽滿順利通過缺水劑層，清理溝流后果。

※機體再生氣量消耗的資金不低于14％

1.好的機筒設計制作，存為100％的吸附物卡路里，吸收的卡路里用在加強回收利用周期的回收利用氣高溫，增加機械的解吸力，導致回收利用更完全。

2.非常干燥和恢復進行交叉自然通風工作方案，濕環境流進干的溶解劑期限果比較好。恢復氣進出口含濕量操作在亞達到飽和情形情形，使消音器原理器及改裝排氣管出入口無冷凝水之慮。

3.可不同干躁機的運動電流消費需求緩解機體降解氣需求量，確保機體降解氣團間斷性安全，機體降解有壓力低至臨界點。

※太干劑利用時間長

1.比較適合的機筒寬度，使氣體根據皮膚干澡劑層的流體密度和時持續好的心態，積極主動發揮出皮膚干澡劑的能力。

2.合情合理的模式配制，在熱空氣加入機筒前，經除油治療快速處理熱空氣中內植物油成分物與重被危害的物，規避低溫干燥劑層受被危害的。

※設備采取了有創意高高質量電動伸縮及液壓閥和靠譜的全電子器件程序把控器序序把控器，組排表面和睦，自己間隔展現雙塔負荷率，配置時間是現場可編，在出廠重設10min。止回閥生存期歷時50萬次運動。

※筒節壁內作冷冷鍍防生銹清理，10年不生繡。

※拉伸動作準確的、機械性能平穩、工作簡便方法，連接不需要基礎性。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆最主要的枝術產品參數 Main technical parameters